
5-Layer Sintered Mesh Filters for Polymer & Synthetic Fiber Industry
The industry-standard polymer melt & spin-pack pre-filter media. Engineered for PET polyester, POY / FDY / BCF spinning, PP / PE / ABS / PA, optical-grade PC, BOPP film, PET bottle recycling and lithium battery separator production.

Industry Characteristics
Why Polymer Melt & Spin-Pack Service Demands Sintered Mesh
Polymer melt filtration combines extreme temperature (220–400 °C), extreme pressure (100–400 bar) and high-viscosity flow — conditions where pleated cartridges and woven mesh fail. The spin-pack and melt-pump positions also demand permanent micron rating that does not drift over 30–90-day production campaigns. Sintered wire mesh is the only media that delivers all of these.
High-Temperature Melt
220–400 °C across PET, PP, PE, PA, PC — only metal media survives.
High-Pressure Service
100–400 bar melt-pump pressure differential — 5-layer diffusion-bonded mesh holds.
Spin-Pack Protection
0.2–0.4 mm spinneret holes demand stable micron rating in front of the spin pack.
Optical-Grade Quality
PC optical, BOPP film, Li-battery separator — sub-micron defects are unacceptable.
Recycled Feedstock
rPET, mixed waste — felt-mesh composite handles heavy contamination loads.
Automatic Back-Flush
Continuous-screen-change melt filters demand sintered mesh that won’t fail under cycling.
Application Coverage
12 Typical Polymer & Fiber Applications — Equipment, Conditions & Recommended Structure
From PET polyester & POY / FDY / BCF spinning, to PP, PE, PA, ABS and optical-grade PC, BOPP film, PET bottle recycling, all the way to lithium battery separator production. Each map to a specific sintered mesh construction.
← Scroll horizontally to view all columns →
| Application Unit | Equipment | Install Location | Working Conditions | Contaminants | Customer Pain Point | Consequence Without Filter | Recommended Structure |
|---|---|---|---|---|---|---|---|
| PET Polyester Line | Polymer Melt Filter | Metering pump, spin pack | 270–320 °C; 100–300 bar | Gels, black specs, carbon | Filament breaks during spinning | Heavy waste-filament production | 5-Layer 316L Sintered |
| POY Spinning Line | Spin-Beam Pre-Filter | Upstream of spinneret | High-temp melt | Unmelted particles | Spinneret hole plugging | Product downgrade | 5-Layer Sintered |
| FDY Production Line | Melt Filter | Spin pack assembly | Continuous production | Gel particles | High filament-break rate | Shutdown for cleaning | High-Precision Sintered |
| BCF Carpet Yarn Line | Melt Filter | Spinneret | High-flow melt | Black specs, gels | Color variation | Product scrap | Sintered Mesh |
| Polypropylene (PP) Plant | Melt Filter | Die head system | 220–300 °C | Carbonized particles | Black-spec defects | Lower product grade | 5-Layer Sintered |
| Polyethylene (PE) Plant | Melt Filter | Extruder die head | High-pressure melt | Unmelted resin | Product defects | Customer complaints | Sintered Mesh |
| ABS Production Line | Melt Filter | Die head | High-viscosity service | Gel particles | Surface defects | Product scrap | High-Strength Sintered |
| PA Nylon Line | Polymer Filter | Spin pack assembly | High-temp / high-pressure | Oxidation particles | Filament breakage | Lower yield rate | 5-Layer Sintered |
| Polycarbonate (PC) Line | Melt Filter | Optical-grade die head | Ultra-clean requirement | Sub-micron particles | Optical defects | High-value product scrap | 7-Layer High-Precision Sintered |
| PET Bottle Recycling Line | Melt Filter | Pelletizer | Recycled feedstock | Metallic particles, debris | Frequent screen changes | Lower output | High-Capacity Felt + Mesh Composite |
| BOPP Film Line | Melt Filter | T-die head | Continuous service | Gels, black specs | Film crystal defects | Off-spec product | High-Precision Sintered |
| Lithium Battery Separator | Melt Filter | Precision die head | Ultra-high precision | Sub-micron particles | Separator defects | Battery performance degradation | Ultra-Precision Electropolished Sintered |
Material Selection
Material & Structure Selection Guide — Polymer Type to Recommended Construction
Construction is matched to polymer melt chemistry, micron requirement and OEM platform. Use this as a starting reference; we tailor to your specific resin and melt conditions.
| Service Polymer | Recommended Material | Rationale |
|---|---|---|
| PET polyester melt | 316L Sintered | Industry-standard configuration for polyester spinning. |
| PP melt | 316L Sintered | Cost-performance balance. |
| PE melt | 316L Sintered | High mechanical strength for HP melt. |
| PA Nylon | 316L Sintered | High-temperature service. |
| PC Optical | 7-Layer High-Precision Sintered | Ultra-clean micron rating for optical applications. |
| Lithium Battery Separator | Electropolished 316L Sintered | Ultra-precision filtration for cell-grade separator. |
| Recycled PET (rPET) | Felt + Mesh Composite | Very high dirt-holding capacity for contaminated feed. |
| Automatic Back-Flush Filter | 5-Layer Sintered | Withstands continuous back-flush cycling. |
| Highly corrosive monomers | Hastelloy C-276 | Maximum chemical corrosion resistance. |
| Chlorine-bearing process | Duplex 2205 | Resists chloride pitting. |
Operating Conditions
Why Sintered Mesh — Mapped to Polymer Melt Conditions
| Condition Type | Working Conditions | Why Stainless Steel Sintered Mesh |
|---|---|---|
| High-Temperature Melt | 220–350 °C | Polymer or resin-bonded media degrade — metal media stay stable. |
| High-Pressure Melt | 100–400 bar | Diffusion-bonded multi-layer construction is collapse-resistant. |
| Continuous Production | 24 h × 365 d | Multi-month service life between change-outs. |
| High-Viscosity Polymer | Large melt flow resistance | Reinforcement layers prevent deformation under high dP. |
| Precision Spinning | 0.2–0.4 mm spinneret holes | Stable micron rating that does not drift in service. |
| Optical-Grade Product | PC, optical film | 7-layer construction captures sub-10 µm defects. |
| Recycled Feedstock | High contaminant content | Felt-mesh composite for very high dirt-holding. |
| Automatic Screen Change | Continuous switching duty | High-strength construction tolerates cycling. |
Customer Concerns
Top 5 Questions from Polymer & Fiber Customers
1. Why is sintered mesh the standard for polymer melt and spin-pack filtration?
add
Polymer melt service combines 220–400 °C, 100–400 bar and very high viscosity — conditions where pleated cartridges and woven mesh collapse or shift micron rating. Sintered wire mesh is diffusion-bonded into a permanent pore structure that survives sustained melt-pump pressure differential for months between change-outs. It’s the standard pre-spinneret filter in every major PET, PP, PE, nylon and BCF plant.
2. Our PP / PE customers are demanding lower black-spec rates. What can we do?
add
Black specs come from gels, carbonized residue and degradation products in the melt. SINFT 5-layer sintered mesh at single-digit micron rating removes these contaminants at the die head, lifting first-pass yield. For premium grades, 7-layer construction delivers even finer cut with stable permanent rating across the campaign.
3. What’s the right filter for lithium battery separator and optical PC service?
add
These are the most demanding polymer melt applications. Lithium battery separator film cannot tolerate sub-micron defects — electropolished 316L 5-layer or 7-layer sintered mesh is the standard. Optical-grade PC uses 7-layer ultra-precision sintered mesh that delivers sub-10 µm rating in 250–350 °C high-pressure melt.
4. PET bottle recycling has heavy contamination. How does SINFT handle it?
add
PET recycling streams carry high loads of metallic particles, dirt and degradation products. SINFT supplies sintered fiber felt + sintered mesh composite construction — far higher capacity per cycle than mesh alone, with the rigidity to survive automatic screen-change cycling on continuous recycle lines.
5. Can SINFT supply sintered mesh elements for automatic screen-change polymer melt filters?
add
Yes. SINFT manufactures sintered mesh elements for major polymer melt filter OEMs (Maag, Gneuss, Erema, Coperion, BKG, Kreyenborg). 5-layer sintered mesh designed to survive continuous back-flush and pressure-reversal cycles. Send drawing or sample for retrofit quote within 24 hours.
Related Products & Applications
Explore Related Solutions
Sintered Mesh Filter
Back to the full product overview, specs and downloads.
Pleated · Polymer & Fiber
Pre-spinneret pleated polishing filter.
Sintered Fiber Felt
High dirt-holding companion for rPET recycling.
Sintered · Petrochemical
Upstream petrochemical catalyst protection & HDS service.
Request a Quote — Polymer & Synthetic Fiber Sintered Mesh
Tell us your polymer (PET, PP, PE, PA, PC, Li-separator…), production scale, melt temperature, melt pump pressure differential and OEM melt filter brand — our engineering team replies with a tailored specification within 24 hours.