
Stainless Steel Basket & Tube Filters for Power Generation Industry
Condenser cooling water, boiler feed pump, condensate, gas turbine fuel, FGD slurry, SCR ammonia, EH oil, steam turbine lube oil, nuclear auxiliary cooling, biomass and waste-to-energy — engineered in 304 / 316L / Duplex 2205 / Super Duplex 2507 / Hastelloy C-276.

Industry Characteristics
Why Power Generation Demands Heavy-Duty Basket & Tube Pre-Filtration
Power generation runs the largest filtration flows in industry. Condenser cooling water on a single unit can reach 30,000–200,000 m³/h. Boiler feed, FGD slurry, EH oil and nuclear auxiliary cooling each demand a different combination of material, micron and structure. Baskets and tube filters protect pumps, exchangers, turbines and servo valves — the assets that define plant availability.
Mega-Flow Cooling
Up to 200,000 m³/h on condenser CCW. DN800–DN1600 multi-basket arrays with 40–75% open area.
High-Pressure Boiler Feed
Boiler feed pumps run continuously at high pressure — protecting them is plant uptime.
EH Oil Servo Valve Protection
Phosphate ester EHC fluid demands 25-50 µm precision to prevent valve spool seizure.
FGD Slurry Wear Resistance
Limestone gypsum slurry is highly abrasive — wedge wire baskets resist rapid blinding.
Nuclear-Grade Ready
NPP auxiliary cooling pre-filters with full material traceability, hydro test and weld documentation.
Seawater & Coastal Service
Coastal power plants need Duplex 2205 / Super Duplex 2507 for chloride resistance.
Application Coverage
15 Typical Power Generation Applications — Equipment, Conditions, Filtration Rating & Material
Covering thermal power, combined-cycle gas turbine, FGD / SCR environmental control, nuclear auxiliary cooling, biomass, waste-to-energy and coastal seawater-cooled stations. Each combination of fluid, temperature and contaminant maps to a specific material, micron rating and structure.
← Scroll horizontally to view all columns →
| Application System | Equipment | Install Location | Service Medium | Working Conditions | Contaminants | Customer Pain Point | Consequence Without Filter | Rating | Type |
|---|---|---|---|---|---|---|---|---|---|
| Recirculating Cooling Water | CCW Pump | Pump inlet | Recirculating water | High-flow, 24×7 | Silt, algae, shells, rust | Pump wear | Pump failure / shutdown | 500–3000 µm | Basket |
| Condenser System | Condenser | Condenser inlet | Cooling water | High flow | Shells, algae, SS | Tube plugging | Vacuum drop, lower output | 1000 µm | Basket |
| Boiler Feed Water | Boiler Feed Pump (BFP) | Feed pump inlet | Demineralized water | High-pressure | Rust, weld slag | BFP impeller wear | Boiler trip | 50–200 µm | Tube |
| Condensate System | Condensate Pump | Condensate pump inlet | Condensate | High-purity water | Iron oxide particles | Pump efficiency drop | System contamination | 25–100 µm | Tube |
| Gas Turbine Fuel System | Gas Turbine Fuel System | Upstream of regulation | Natural gas | HP gas | Rust, weld slag | Nozzle plugging | Abnormal combustion | 10–50 µm | Tube |
| Oil-Fired Power Station | Fuel Oil Transfer Pump | Transfer pump inlet | Diesel / HFO | Continuous | Rust, sludge | Pump wear | Fuel supply interruption | 100–500 µm | Basket |
| FGD (Flue Gas Desulfurization) | Slurry Circulation Pump | Pump inlet | Limestone slurry | High-wear duty | Gypsum, mineral particles | Slurry pump wear | Lower SO₂ removal | 500–2000 µm | Basket |
| SCR DeNOx | Ammonia Injection System | Upstream of metering pump | Aqueous ammonia | Corrosive duty | Crystal particles | Injector plugging | NOx exceedance | 50–100 µm | Tube |
| Closed Cooling Water | Closed Cooling Water System | Circulation pump inlet | Closed cooling water | Long-cycle service | Rust, scale | Heat exchanger fouling | Temperature exceedance | 100–500 µm | Basket |
| Steam Turbine Lube Oil | Steam Turbine Lubrication System | Lube pump inlet | Turbine oil | Continuous | Metal particles, sludge | Oil pump wear | Bearing damage | 50–150 µm | Tube |
| EH Fire-Resistant Fluid | Electro-Hydraulic Control System | EH oil pump inlet | Phosphate ester EHC | HP control system | Metal particles | Servo valve seizure | Turbine trip | 25–50 µm | Tube |
| NPP Auxiliary Cooling | Auxiliary Cooling System | Cooling system inlet | Deionized water | High safety class | Weld slag, oxides | System contamination | Safety risk | 25–100 µm | Tube |
| Biomass Power Generation | Biomass Transfer System | Transfer pump inlet | Biomass oil | High viscosity | Wood chips, char | Pipe plugging | Shutdown for cleaning | 200–1000 µm | Basket |
| Waste-to-Energy Leachate | Leachate Treatment | Circulation pump inlet | Landfill leachate | High-contaminant | Solid suspended matter | Pump body plugging | System shutdown | 500–3000 µm | Basket |
| Coastal Seawater-Cooled Plant | Seawater Lift Pump | Pump inlet | Seawater | High-chloride corrosion | Shells, algae, silt | Marine biofouling | Exchanger plugging | 1000–5000 µm | Basket |
Material Selection
Material Selection Guide — Service Environment to Recommended Alloy
Material is matched to chloride load, corrosive species and abrasion. Use this as a starting reference; we tailor to your fluid analysis.
| Service Environment | Recommended Material | Rationale |
|---|---|---|
| General recirculating water | SS 304 | Cost-effective default with adequate corrosion resistance. |
| Industrial cooling water | SS 316L | Higher Mo content for better corrosion resistance. |
| Boiler feed water | SS 316L | Stable in pure-water service. |
| Condensate system | SS 316L | Prevents secondary contamination. |
| Natural gas system | 316L Sintered Mesh Tube | High pressure rating. |
| Lube oil system | 316L Woven Mesh | Easy cleaning. |
| EH fire-resistant fluid | 316L Sintered Mesh | Stable micron rating critical for servo valves. |
| FGD slurry | 316L Wedge Wire | Anti-blinding profile resists abrasive gypsum slurry. |
| Seawater cooling | Duplex 2205 | Resists chloride pitting. |
| Coastal plant seawater | Super Duplex 2507 | Maximum chloride corrosion resistance. |
| Strong acid service | Hastelloy C-276 | Resists severe chemical corrosion. |
Technical Specifications
SINFT Power Plant Basket & Tube Filter — Key Parameters
Engineering targets we hit on every power generation project.
Diameter Range
DN800–1600
Mega-bore baskets for condenser CCW.
Open Area
40–75%
Maximum flow capacity, minimum dP.
Flow Capacity
Up to 200,000 m³/h
Multi-basket parallel configurations.
EH Oil Rating
25–50 µm
Servo valve protection grade.
Construction
Fully Welded
Vibration-proof, long-life service.
Wear Resistance
Wedge Wire
Anti-blinding profile for FGD slurry.
Cleanability
Backwash + CIP
Cleanable, reusable across multi-cycle service.
Nuclear Quality
NQA-1 Ready
ASME III Class 3 traceability available.
Customer Concerns
Top 5 Questions from Power Generation Customers
1. How big a basket filter do power plants actually need?
add
Very big. Condenser circulating cooling water on a single 600 MW unit can run 30,000–200,000 m³/h. SINFT delivers DN800–DN1600 basket strainers in multi-basket parallel configurations with very large open area (40–75%) to keep dP minimal. For coastal seawater cooling we provide Duplex 2205 baskets at 1000–5000 µm to intercept shells and biofouling.
2. What’s special about EH (electro-hydraulic) oil filtration?
add
Phosphate ester EHC fluid is aggressive to common seal materials and demands very clean service to protect servo valves. SINFT 25–50 µm 316L sintered mesh tube filters with FKM-compatible end caps are field-proven on EH oil systems for the largest steam turbine OEMs. Filter cleanliness directly drives turbine availability.
3. What materials do you use for FGD slurry duty?
add
FGD limestone slurry is highly abrasive. We use 316L wedge wire baskets at 500–2000 µm — the anti-blinding wedge profile resists rapid plugging by gypsum and mineral particles, while 316L delivers acceptable corrosion resistance to the sulfate-bearing service.
4. Can SINFT supply filters to nuclear (ASME III / NQA-1) requirements?
add
Yes — for NPP auxiliary cooling and condensate polishing pre-filters, SINFT can supply nuclear-grade 316L tube filters with full material traceability, dimensional inspection, hydrostatic test and weld documentation. Specific ASME III Class 3 / NQA-1 certification is available on request.
5. Why use basket and tube instead of pleated cartridges in a power plant?
add
Pleated cartridges deliver high precision at low flow. Power-plant systems run very high flows — condenser cooling, boiler feed, FGD slurry. Baskets and tube filters provide bulk pre-filtration at minimum dP, protecting expensive pumps, exchangers and turbines. Pleated cartridges are downstream of the basket for final polish where required.
Related Products & Applications
Explore Related Solutions
Basket Filters & Strainers
Back to the full product overview, specs and downloads.
Power Generation Overview
Full power generation application portfolio.
Basket & Tube · Petrochemical
FCC, hydrocracking, ethylene and refinery service.
Basket & Tube · Marine & Offshore
Seawater, BWTS, FPSO and offshore platform service.
Request a Quote — Power Generation Basket & Tube Filters
Tell us your plant type (thermal / CCGT / nuclear / biomass / WtE / coastal), system (CCW, BFP, EH oil, FGD, SCR…), flow rate and water chemistry — our engineering team replies with a tailored specification within 24 hours.